# Connecting to a Universal Robot for read and write

**URL:** <https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097>\
**Category:** Ignition\
**Created:** [April 15, 2025, 7:58am UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097 "2025-04-15T07:58:18Z")\
**Posts on this page:** 8\
**Page:** 2

<div class="post-metadata">

**Author:** ![jacob.cobb](https://avatars.discourse-cdn.com/v4/letter/j/c5a1d2/32.png) [@jacob.cobb](https://forum.inductiveautomation.com/u/jacob.cobb)\
**Post date:** [June 18, 2025, 7:46pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/22 "2025-06-18T19:46:17Z")

</div>

Still getting '0' with that change. Strangely, I'm getting '0' no matter what number I put after HRF. I even tried 260 which is robot powered on, still getting '0'

---

<div class="post-metadata">

**Author:** ![Marcus\_Sysum](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/marcus_sysum/32/57944_2.png) [@Marcus\_Sysum](https://forum.inductiveautomation.com/u/Marcus_Sysum)\
**Post date:** [June 18, 2025, 7:48pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/23 "2025-06-18T19:48:27Z")

</div>

You don't Need the node id info in the opc item path `[UR3 Modbus]HR255`is valid.

 ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/e/4/e493f61a59f86ad1404935454a73941f2b956a7b.png)  
This image is reading from port\_resgister 128 of the robot with zero based addressing.  
 ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/6/0/6048be90d295c69a7fdf3edcebd81818cc8e3591.png)  
I just realized he using HRF. Try HR to verify that you are reading the correct registers.

---

<div class="post-metadata">

**Author:** ![jacob.cobb](https://avatars.discourse-cdn.com/v4/letter/j/c5a1d2/32.png) [@jacob.cobb](https://forum.inductiveautomation.com/u/jacob.cobb)\
**Post date:** [June 18, 2025, 7:53pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/24 "2025-06-18T19:53:41Z")

</div>

I'm replying here on behalf of Cody Chamberlain. You were assisting him earlier but he ran out of replies as a new user. I have a meeting to go to, so if there is some way around that restriction, please message him further. If not, you can email him at [Cody.Chamberlain@brother.com](mailto:Cody.Chamberlain@brother.com).

---

<div class="post-metadata">

**Author:** ![ryan.white](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/ryan.white/32/73193_2.png) [@ryan.white](https://forum.inductiveautomation.com/u/ryan.white)\
**Post date:** [June 18, 2025, 7:55pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/25 "2025-06-18T19:55:35Z")

</div>

> [@Marcus\_Sysum](#):
>
> I just realized he using HRF.

That was due to me recommending that, as they had the tag configured as a Float. I assumed they were attempting to pass a float from the robot to Ignition.

---

<div class="post-metadata">

**Author:** ![Marcus\_Sysum](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/marcus_sysum/32/57944_2.png) [@Marcus\_Sysum](https://forum.inductiveautomation.com/u/Marcus_Sysum)\
**Post date:** [June 18, 2025, 7:55pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/26 "2025-06-18T19:55:46Z")

</div>

I would Try HRI to get two consecutive registers not a HRF.

---

<div class="post-metadata">

**Author:** ![Marcus\_Sysum](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/marcus_sysum/32/57944_2.png) [@Marcus\_Sysum](https://forum.inductiveautomation.com/u/Marcus_Sysum)\
**Post date:** [June 18, 2025, 7:58pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/27 "2025-06-18T19:58:19Z")

</div>

It was never discussed what the register was actually. So i wasn't sure how big the value would be.

So It turns out the ur robot needs the unsigned conversion [UR3 Modbus]HRUS255 will bring the full 16 bit value.  
I tested this on a ursim passing in a value of 65534 to a variable and writing to the port register 128

 ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/7/3/730e1359a83cb329d539c6404bb7a7c0be9e64c2.png)

---

<div class="post-metadata">

**Author:** ![kenneth.bell](https://avatars.discourse-cdn.com/v4/letter/k/bb73d2/32.png) [@kenneth.bell](https://forum.inductiveautomation.com/u/kenneth.bell)\
**Post date:** [October 7, 2026, 4:38pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/28 "2026-10-07T16:38:35Z")

</div>

Continuing the discussion from [Connecting to a Universal Robot for read and write](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097):

Marcus: You were working with Cody Chamberlin in 2025 on a script to collect data from a UR robot. Do you have the python script ‘python3.12 Dashboard\_csv.py’ that you wrote for him.

Kenneth Bell

---

<div class="post-metadata">

**Author:** ![Marcus\_Sysum](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/marcus_sysum/32/57944_2.png) [@Marcus\_Sysum](https://forum.inductiveautomation.com/u/Marcus_Sysum)\
**Post date:** [October 7, 2026, 4:59pm UTC](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097/29 "2026-10-07T16:59:31Z")

</div>

I sent you a DM about it.

[Previous page](https://forum.inductiveautomation.com/t/connecting-to-a-universal-robot-for-read-and-write/105097.md?page=1)
