# RS Logix Emulator communication with Ignition SCADA **URL:** \ **Category:** Ignition\ **Tags:** ignition80\ **Created:** [July 5, 2020, 11:33am UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367 "2020-07-05T11:33:52Z")\ **Posts on this page:** 14\ **Page:** 1
**Author:** ![Sandeep\_Bakoliya](https://avatars.discourse-cdn.com/v4/letter/s/43a26b/32.png) [@Sandeep\_Bakoliya](https://forum.inductiveautomation.com/u/Sandeep_Bakoliya)\ **Post date:** [July 5, 2020, 11:33am UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/1 "2020-07-05T11:33:52Z")
Dear Experts, I am new to Ignition SCADA. I want to communicate RS Logix Emulator to Ignition SCADA 8.04. What is the procedure to set up communication between Ignition SCADA and rs Logix emulator. Thanks & Regards Sandeep Bakoliya ---
**Author:** ![Kuskah](https://avatars.discourse-cdn.com/v4/letter/k/7993a0/32.png) [@Kuskah](https://forum.inductiveautomation.com/u/Kuskah)\ **Post date:** [July 5, 2020, 1:28pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/2 "2020-07-05T13:28:45Z")
While this is possible, it is not easy. If you are just wanting to use simulated tags you may want to look into using the simulation drivers. You can find information on these driver here: [https://docs.inductiveautomation.com/display/DEP/Simulators](https://docs.inductiveautomation.com/display/DEP/Simulators) If you really want to use the logix emulator, you have to get FactoryTalk Linx Gateway and get that installed. Then you have to configure an OPC UA connection to Factorytalk. It took me a lot of trial and error to get this to work, but it is possible. There just aren’t any documents that I have found that gives you a step by step on how to do this. ---
**Author:** ![jlandwerlen](https://avatars.discourse-cdn.com/v4/letter/j/bc8723/32.png) [@jlandwerlen](https://forum.inductiveautomation.com/u/jlandwerlen)\ **Post date:** [July 5, 2020, 4:05pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/3 "2020-07-05T16:05:25Z")
Here’s a walkthrough for Linx Gateway: [Ignition Tips, Tricks, and Cheats](https://godboutpcs.com/blog/f/ignition-tips-tricks-and-cheats) Also, the guys doing Flintium project stated they managed to get v32 emulate to work pointed straight to the Logix driver. I wasn’t able to get it to work, but maybe you will have better luck. > **[jlbcontrols/Flintium](https://github.com/jlbcontrols/Flintium/wiki/Setting-up-RSLogix-Emulate)** > > Open-source library of Ignition® faceplates and graphics that pair with AOIs from the Rockwell Automation® Library of Process Objects. - jlbcontrols/Flintium ---
**Author:** ![joseph.burns](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/joseph.burns/32/61584_2.png) [@joseph.burns](https://forum.inductiveautomation.com/u/joseph.burns)\ **Post date:** [July 8, 2020, 4:42pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/4 "2020-07-08T16:42:01Z")
@tordvd Were you able to connect to Emulate v32 using the method in the Flintium Wiki? ---
**Author:** ![tordvd](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/tordvd/32/11525_2.png) [@tordvd](https://forum.inductiveautomation.com/u/tordvd)\ **Post date:** [July 8, 2020, 5:04pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/5 "2020-07-08T17:04:35Z")
I havent had the chance to try it yet. I am going to to a project for a customer in plantpax 3.x something after the summer, and will probably try it then. I probably can take a look at the alarming at the same time… ---
**Author:** ![jlandwerlen](https://avatars.discourse-cdn.com/v4/letter/j/bc8723/32.png) [@jlandwerlen](https://forum.inductiveautomation.com/u/jlandwerlen)\ **Post date:** [July 10, 2020, 2:18pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/6 "2020-07-10T14:18:44Z")
I use VM images. I had one image with Win7x64 and installed Emulate v32. I couldn’t get things to work. I used an image with Win10x64 and installed Emulate v32. This worked using both processor versions of 30 and 32 (I didn’t try any more than those). So, not sure what the differences are. I’m guessing Windows as I have the same core software installed on both images. But, from my brief test, as long as you have Emulate 32 installed, you can still use the following processor versions… 20, 21, 21.03, 23, 24, 28, 30, 31, & 32. When you install Emulate v32, those get installed as well. Matter of fact, you may have to remove/uninstall earlier versions of Emulate to install Emulate v32. I’m assuming since 30 & 32 worked, the rest will as well. ---
**Author:** ![Dmart](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/dmart/32/13427_2.png) [@Dmart](https://forum.inductiveautomation.com/u/Dmart)\ **Post date:** [January 10, 2021, 6:53pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/7 "2021-01-10T18:53:31Z")
Is your Ignition and Rockwell software in the same VM or in different VM’s. Mine are in separate VM’s and I have not been able to get this to work. Ignition says “ReconnectWait” ---
**Author:** ![jlandwerlen](https://avatars.discourse-cdn.com/v4/letter/j/bc8723/32.png) [@jlandwerlen](https://forum.inductiveautomation.com/u/jlandwerlen)\ **Post date:** [January 10, 2021, 7:52pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/8 "2021-01-10T19:52:03Z")
Mine were separate. ---
**Author:** ![Dmart](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/dmart/32/13427_2.png) [@Dmart](https://forum.inductiveautomation.com/u/Dmart)\ **Post date:** [January 12, 2021, 2:45am UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/9 "2021-01-12T02:45:53Z")
Thanks Well, It’s good to hear what I’m trying should be able to work. Now I just have to figure out why it’s not working for me. ---
**Author:** ![Jack\_Danby](https://avatars.discourse-cdn.com/v4/letter/j/f475e1/32.png) [@Jack\_Danby](https://forum.inductiveautomation.com/u/Jack_Danby)\ **Post date:** [April 20, 2023, 5:44am UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/10 "2023-04-20T05:44:29Z")
Were you able to get this working? i am only able to get the same status as you, “ReconnectWait” ---
**Author:** ![Simen\_Minerd](https://avatars.discourse-cdn.com/v4/letter/s/e274bd/32.png) [@Simen\_Minerd](https://forum.inductiveautomation.com/u/Simen_Minerd)\ **Post date:** [April 20, 2023, 3:00pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/11 "2023-04-20T15:00:30Z")
Use OPC-DA COM It work fine. You can even create device connection using this model under OPC UA, but it has lots issue with device connection. Anyway, you do not need to connect Emulator as a device, just use OPC-DA COM you can navigate to your OPC topic, Run you RSLinx as server. ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/7/7/777595259fb348603f65405c85a5f4bd74a309f9.png) ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/f/f/ff794c2941eb7c7653713339bb6fbc8c2723092f.png) ![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/5/b/5b9b08d6e7b8c2acd4d7328827c96cbd942ddc77.png) ---
**Author:** ![Simen\_Minerd](https://avatars.discourse-cdn.com/v4/letter/s/e274bd/32.png) [@Simen\_Minerd](https://forum.inductiveautomation.com/u/Simen_Minerd)\ **Post date:** [April 20, 2023, 3:05pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/12 "2023-04-20T15:05:58Z")
[OPC-UA to RSLogix5000 Emulator? - Ignition - Inductive Automation Forum](https://forum.inductiveautomation.com/t/opc-ua-to-rslogix5000-emulator/4849/13) Follow choy 's instruction ---
**Author:** ![pturmel](https://sea1.discourse-cdn.com/inductiveautomation/user_avatar/forum.inductiveautomation.com/pturmel/32/3295_2.png) [@pturmel](https://forum.inductiveautomation.com/u/pturmel)\ **Post date:** [April 20, 2023, 3:18pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/13 "2023-04-20T15:18:28Z")
Connecting via OPC precludes easy substitution of Ignition's native Logix driver when the work is moved to production. If you can set up as described in the Flintium link, that would be preferred. Note that FactoryTalk Linx and/or RSLinx must be configured to claim local port 44818 to accept incoming connections (and the firewall opened). That isn't shown in the Flintium doc. ---
**Author:** ![Simen\_Minerd](https://avatars.discourse-cdn.com/v4/letter/s/e274bd/32.png) [@Simen\_Minerd](https://forum.inductiveautomation.com/u/Simen_Minerd)\ **Post date:** [April 20, 2023, 3:24pm UTC](https://forum.inductiveautomation.com/t/rs-logix-emulator-communication-with-ignition-scada/36367/15 "2023-04-20T15:24:49Z")
![image](https://us1.discourse-cdn.com/inductiveautomation/original/3X/0/c/0c461dee1455973f0cd0b55433ad0e7aed20eca8.png)